[Aurora-sparc-user] Sun Netra T1 (105) with Disk Pack .. possible uses??

[Plasma]

Houston we have lift off ..... Phoned a friend who's a Sun engineer, turns
out thru the emulation program I was using its ALT-B not CTRL-B ... lol ..
anyway I've now reset the environment settings and disabled auto boot. Just
need to replace the CD with a DVD rom then find my Aurora 2.0 disk! :)

Kevin

-----Original Message-----
From: aurora-sparc-user-bounces at lists.auroralinux.org
[mailto:aurora-sparc-user-bounces at lists.auroralinux.org] On Behalf Of Plasma
Sent: 24 March 2007 14:06
To: 'Aurora user discussion'
Subject: RE: [Aurora-sparc-user] Sun Netra T1 (105) with Disk Pack ..
possible uses??

Thanks for that Jos, at least I know where I should be doing the escape
character. I've tried with ProComm Plus and with HyperTerminal but neither
are able to get me to the "ok" prompt. I get the Open Boot message then
"Initialising Memory /" but it just ignores any sequence I send it and
continues to boot Solaris. I'm also using a genuine blue Cisco Console
cable, I'm going to try from a different PC and maybe some other Terminal
emulation programs see if that helps.

Kevin

-----Original Message-----
From: aurora-sparc-user-bounces at lists.auroralinux.org
[mailto:aurora-sparc-user-bounces at lists.auroralinux.org] On Behalf Of Jos
van der Ende
Sent: 24 March 2007 13:31
To: aurora-sparc-user at lists.auroralinux.org
Subject: Re: [Aurora-sparc-user] Sun Netra T1 (105) with Disk Pack ..
possible uses??

On Sat, 24 Mar 2007 12:37:18 -0000
"Plasma" <plasma.m at ukonline.co.uk> wrote:

> Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
> OpenBoot 3.10.24 ME, 512 MB memory installed, Serial #11725577.
> Ethernet address 8:0:20:b2:eb:9, Host ID: 80b2eb09.

Once you reach this point, and before Solaris boots (which is
what happens now), you should generate a break over the serial
line. How that is done depends entirely on your terminal
emulator, but control-A or control-B are common.

If done correctly, you should see a prompt like this:

OK>

That is the OBP. When installing a system, I usually execute the
following two commands:

set-defaults
setenv auto-boot? false

The first resets the system to its factory defaults, and the second
prevents the starting of the OS on powerup, making it more convenient
to boot from a different medium.


Also, when using a Netra t1, make sure you have the correct serial
cable. A 'rollover cable' (also known as a 'cisco cable') works best
for me. This is a (usually flat) cable with RJ45 jacks on both ends,
but unlike a normal UTP cable, the jacks are wired reversed of each
other. (Not to be confused with a cross cable, which only has read
and write reversed.)


Jos
_______________________________________________
Aurora-sparc-user mailing list
Aurora-sparc-user at lists.auroralinux.org
http://lists.auroralinux.org/mailman/listinfo/aurora-sparc-user
Aurora FAQ: http://www.ecs.soton.ac.uk/~mas01r/aurorafaq.html


__________ NOD32 2142 (20070324) Information __________

This message was checked by NOD32 antivirus system.
http://www.eset.com


_______________________________________________
Aurora-sparc-user mailing list
Aurora-sparc-user at lists.auroralinux.org
http://lists.auroralinux.org/mailman/listinfo/aurora-sparc-user
Aurora FAQ: http://www.ecs.soton.ac.uk/~mas01r/aurorafaq.html


__________ NOD32 2142 (20070324) Information __________

This message was checked by NOD32 antivirus system.
http://www.eset.com